Before starting setup, decide on the most suitable connection method for the machine.
This machine can be used over a wireless or wired LAN, as well as via USB connection.

To use the machine by connecting it to a computer, software including the drivers needs to be copied (installed) to the computer's hard disk, and setting configured
according to the connection method. In addition, configure the machine's LAN settings to connect to the network. Read the following carefully before starting setup.

Notes on Setup

• Quit all running applications before installation.
• Log into a user account with the administrator privilege.
• Do not switch user accounts during installation.
• It may be necessary to restart your computer during the installation process. Follow the on-screen instructions and click OK, and do not remove the Setup CD-ROM during restarting. The installation resumes from where it left off when your computer has been restarted.
• Since Mac OS 9, Mac OS X Classic environments, Mac OS X v.10.3.8 or earlier are not supported.

Notes on Network Connection

• Before connecting the machine to the network, confirm that configuration of the computer and network devices (router, access point, etc.) complete, and that the computer can connect to the network.
• For information on how to confirm the settings of the access point, refer to your access point's instruction manual or contact its manufacturer. For example,

- Disable Stealth (closed network) function
- Confirm MAC address
- Disable the access point's IP address

• The configuration, router functions, setup procedures and security functions of the network device vary depending on your environment. For details, refer to your device's instruction manual or contact its manufacturer.
• If the firewall function of your security software is turned on the warning message may appear that Canon software is attempting to access the network.

If the warning message appears, set the security software to always allow access.

• In an office setup, consult your network administrator.

Note on Wired LAN Connection

• A router and LAN cable are required to connect the machine to a wired LAN.

These must be purchased separately.

Notes on Wireless LAN Connection

• Ad-hoc mode is not supported.
• If you connect to a network that is not protected with security measures, there is a risk of disclosing data such as your personal information to a third party.
• The machine may communicate with other access points used in the vicinity.
• The machine supports WPS (Wi-Fi Protected Setup) and WCN (Windows Connect Now) in addition to the conventional wireless LAN settings. As for WCN, "WCN-UFD" that requires a USB flash drive is supported.

Preparation for Setup

USB

USB

• A:USB cable

Windows

NOTE
If the Found New Hardware or Found New Hardware Wizard screen appears:

(1) Remove the USB cable connected to your computer.
The screen may close. In this case, proceed from 1.
(2) Click Cancel to quit the screen.
(3) Proceed from 1.

1. Press the ON button (A) to TURN OFF THE MACHINE.

IMPORTANT
Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing.

2. Turn on the computer, then insert the
Setup CD-ROM into the CD-ROM drive.
The setup program should run automatically.

• Windows Vista:

Go to Step 3

• Windows XP/2000:

Go to Step 5

REFERENCE
If the program does not start automatically, double-click the CD-ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

3. AutoPlay screen appears, click Run Msetup4.exe.

4. User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8.　Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

• USB Connection

1. On the Setup Method screen, select Use the printer via USB, then click Next.

2. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine.

IMPORTANT

• When the machine is recognized by the computer, a message appears on the screen.
• If you cannot go to the next procedure after 10 minutes, click Help and confirm the message.

REFERENCE
The USB port is located on the right side at the back of the machine.

• Information

1. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

2. Click Next.
It may take a while for the next screen to appear. Click Next only once.

3. Click Next.
If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

4. When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

5. Click Exit.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

Macintosh

1. Connect one end of the USB cable to the computer and the other to the machine.
Make sure the machine is turned on.

REFERENCE

• The USB port is located on the right side at the back of the machine.
• When using WPS (Wi-Fi Protected Setup) or connecting an

additional computer, make sure that the machine is turned on, then go to step 2. It is not necessary to connect the machine to the computer with a USB cable.

2. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

3. Double-click the Setup icon.
If the CD-ROM folder does not open automatically, double-click the CANON_IJ icon on the desktop.

4. Enter your administrator name and password. Click OK.
If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8. Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

9. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

10. Click Next.

11. Click Next.
If connected to the Internet, the user registration page appears.
Follow the on-screen instructions to register your product.
You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

12. Click Restart.
When the computer restarts, Canon IJ Network Tool starts automatically.
Click Restart to restart the computer.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

REFERENCE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.

• USB Connection

On the Canon IJ Network Tool screen, select USB connection, then click OK.

Install the Software (USB Connection)

Wired LAN

Wired LAN

• B:LAN cable
• C:Router

IMPORTANT

• Before connecting the machine to the network, confirm that configuration of the computer and network devices (router, access point, etc.) is complete, and that the computer can connect to the network. For the procedures to connect a network device to the computer and set them up, refer to the manual of your network device or contact its manufacturer.
• The machine cannot be used over a wired and wireless LAN at the same time.

Machine's LAN Setting

1. Use the Easy-Scroll Wheel (A) or the or button to select Settings, then press the OK button.

2. Select Device settings, then press the OK button.

3. Select LAN settings, then press the OK button.

4. Select Change wireless/wired, then press the OK button.

5. Select either to the connection method, then press the OK button.

Windows

NOTE
If the Found New Hardware or Found New Hardware Wizard screen appears:

(1) Remove the USB cable connected to your computer.
The screen may close. In this case, proceed from 1.
(2) Click Cancel to quit the screen.
(3) Proceed from 1.

1. Press the ON button (A) to TURN OFF THE MACHINE.

IMPORTANT
Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing.

2. Turn on the computer, then insert the
Setup CD-ROM into the CD-ROM drive.
The setup program should run automatically.

• Windows Vista:

Go to Step 3

• Windows XP/2000:

Go to Step 5

REFERENCE
If the program does not start automatically, double-click the CD-ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

3. AutoPlay screen appears, click Run Msetup4.exe.

4. User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8.　Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

• First-time Setup for Use over Wired LAN

1. On the Setup Method screen, select Connect printer to the network for the first time, then click Next.

When a confirmation screen for the machine's LAN setting appears, click OK.

IMPORTANT
Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to "Machine's LAN Setting".

2. Prepare Cables

Confirm that USB Cable(A) and LAN Cable(B) are Ready.

3. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine.

Set up the machine over a USB connection until the network connection is complete.

IMPORTANT
The machine is recognized by the computer, then message appears on the screen.
If you cannot go to the next procedure after 10 minutes, click Help and confirm the message.

REFERENCE
The USB port is located on the right side at the back of the machine.

4. When the Setup Preparations dialog box appears, confirm that preparation is complete, then click Next.

5. Connect the machine to the network device with a LAN cable(A), then click Yes.

6. Detect the Machine.
When the Set Printer IP Address screen appears, click Connect.

If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to the following procedure.

• Windows Vista:

Go to Step 8

• Windows XP/2000:

Go to Step 7

7. Windows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

8. When the Setup Completion dialog box appears, remove the USB cable, then click Finish.

REFERENCE

• To change the port name, click View Setup Results, then click Set Port Name.
• If Unsafe Removal of Device is displayed, click OK.

• Information

1. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

2. Click Next.
It may take a while for the next screen to appear. Click Next only once.

3. Click Next.
If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

4. When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

5. Click Exit.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

Macintosh

1. Connect one end of the USB cable to the computer and the other to the machine.
Make sure the machine is turned on.

REFERENCE

• The USB port is located on the right side at the back of the machine.
• When using WPS (Wi-Fi Protected Setup) or connecting an

additional computer, make sure that the machine is turned on, then go to step 2. It is not necessary to connect the machine to the computer with a USB cable.

2. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

3. Double-click the Setup icon.
If the CD-ROM folder does not open automatically, double-click the CANON_IJ icon on the desktop.

4. Enter your administrator name and password. Click OK.
If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8. Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

9. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

10. Click Next.

11. Click Next.
If connected to the Internet, the user registration page appears.
Follow the on-screen instructions to register your product.
You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

12. Click Restart.
When the computer restarts, Canon IJ Network Tool starts automatically.
Click Restart to restart the computer.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

REFERENCE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.

• First-time Setup for Use over Wired LAN

1. On the Canon IJ Network Tool screen, select LAN connection, then click OK.

IMPORTANT
Set the machine's LAN setting to Wired LAN active beforehand. For details, refer to "Machine's LAN Setting".

2. If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK.

3. Select Setup in the pop-up menu, select **** series in Printers, then click OK.
To set up a machine that is not yet connected to a LAN, connect to it by USB.

REFERENCE

• [****] is your machine's name.
• If no printer is detected, click OK. Make sure of the following, then click Update.

- The machine is connected to the computer with a USB cable.
- The machine is turned on.

4. Connect the machine to the network device with a LAN cable (A), then click Yes.

5. When the Setup Completion dialog box appears, remove
the USB cable, then click OK.

The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.

• Add the Machine

1. Mac OS X v.10.4.x/v.10.3.9

When the Printer List screen appears, click Add.
Mac OS X v.10.4.x:
Go to Step 2
Mac OS X v.10.3.9:
Go to Step 3

NOTE
In the following instructions, "****" signifies your machine's name.

2. Mac OS X v.10.5.x/v.10.4.x

Wait for a while, then select Canon **** series and click Add.
In Mac OS X v.10.4.x, click More Printers in the Printer Browser screen.
- Mac OS X v.10.5.x:
Go to Step 5
- Mac OS X v.10.4.x:
Go to Step 3

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

3. Mac OS X v.10.4.x/v.10.3.9

Select Canon IJ Network in the pop-up menu, select your machine's name in the list of printers, then click Add.

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

4. Mac OS X v.10.4.x/v.10.3.9

Confirm that your machine's name is added to the list of printers.

5.

On the Canon IJ Network Scanner Selector screen, select Canon **** series Network in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner.

REFERENCE
With Mac OS X v.10.5.x, the Card Slot is not available when using the machine over a network.

Install the Software (First-time Setup for Use over Wired LAN)

Wireless LAN

Wireless LAN

• D:Access point

IMPORTANT

• Before connecting the machine to the network, confirm that configuration of the computer and network devices (router, access point, etc.) is complete, and that the computer can connect to the network. For the procedures to connect a network device to the computer and set them up, refer to the manual of your network device or contact its manufacturer.
• The machine cannot be used over a wired and wireless LAN at the same time.

Machine's LAN Setting

1. Use the Easy-Scroll Wheel (A) or the or button to select Settings, then press the OK button.

2. Select Device settings, then press the OK button.

3. Select LAN settings, then press the OK button.

4. Select Change wireless/wired, then press the OK button.

5. Select either to the connection method, then press the OK button.

Windows

NOTE
If the Found New Hardware or Found New Hardware Wizard screen appears:

(1) Remove the USB cable connected to your computer.
The screen may close. In this case, proceed from 1.
(2) Click Cancel to quit the screen.
(3) Proceed from 1.

1. Press the ON button (A) to TURN OFF THE MACHINE.

IMPORTANT
Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing.

2. Turn on the computer, then insert the
Setup CD-ROM into the CD-ROM drive.
The setup program should run automatically.

• Windows Vista:

Go to Step 3

• Windows XP/2000:

Go to Step 5

REFERENCE
If the program does not start automatically, double-click the CD-ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

3. AutoPlay screen appears, click Run Msetup4.exe.

4. User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8.　Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

• First-time Setup for Use over Wireless LAN

1. On the Setup Method screen, select Connect printer to the network for the first time, then click Next.

When a confirmation screen for the machine's LAN setting appears, click OK.

IMPORTANT
Set the machine's LAN setting to Wireless LAN active beforehand. For details, refer to "Machine's LAN Setting".

2. When the Printer Connection screen appears, connect the machine to the computer with a USB cable, then turn on the machine.

Set up the machine over a USB connection until the network connection is complete.

IMPORTANT
When the machine is recognized by the computer, a message appears on the screen.
If you cannot go to the next procedure after 10 minutes, click Help and confirm the message.

REFERENCE
The USB port is located on the right side at the back of the machine.

3. When the Setup Preparations dialog box appears, confirm that preparation is complete, then click Next.

4. Detect Access Point.

When the Access Points screen appears, select an access point to use, then click Connect.
When an access point is detected automatically, the Access Points screen does not appear. Go to step 5.

IMPORTANT
To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Key, then click Connect.

5. Detect the Machine.
When the Set Printer IP Address screen appears, click Connect.

If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to the following procedure.

• Windows Vista:

Go to Step 7

• Windows XP/2000:

Go to Step 6

NOTE
If no connection is established even after Connect is clicked.

6. Windows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

7. When the Setup Completion dialog box appears, remove the USB cable, then click Next.

REFERENCE

• To change the port name, click View Setup Results, then click Set Port Name.
• If Unsafe Removal of Device is displayed, click OK.

8. Turn off the machine, then place the machine in the location where you will use it, and turn on it.

9. On the Connection Performance Measurement screen, click Next.

Measuring of the communication status starts, and the results are displayed.

REFERENCE
Measuring takes a few minutes. You can cancel measuring by clicking Cancel.
You also examine the detailed status of the communication link after setup by using the Canon IJ Network Tool.

10. Confirm the measurement results, then click Finish.

Ensure that is displayed in Connection performance between the printer and the access point.

REFERENCE

• If any symbol other than is displayed, refer to displayed comments and Help for improving the status of communication link.
• To check whether the new location is better, click Remesurement. Measurement of the communication status is performed again.
• When any message on Overall network performance appears in the measurement results, rearrange the printer and other network devices following the instructions on the screen.

• Information

1. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

2. Click Next.
It may take a while for the next screen to appear. Click Next only once.

3. Click Next.
If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

4. When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

5. Click Exit.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

Macintosh

1. Connect one end of the USB cable to the computer and the other to the machine.
Make sure the machine is turned on.

REFERENCE

• The USB port is located on the right side at the back of the machine.
• When using WPS (Wi-Fi Protected Setup) or connecting an

additional computer, make sure that the machine is turned on, then go to step 2. It is not necessary to connect the machine to the computer with a USB cable.

2. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

3. Double-click the Setup icon.
If the CD-ROM folder does not open automatically, double-click the CANON_IJ icon on the desktop.

4. Enter your administrator name and password. Click OK.
If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8. Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

9. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

10. Click Next.

11. Click Next.
If connected to the Internet, the user registration page appears.
Follow the on-screen instructions to register your product.
You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

12. Click Restart.
When the computer restarts, Canon IJ Network Tool starts automatically.
Click Restart to restart the computer.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

REFERENCE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.

• First-time Setup for Use over Wireless LAN

1. On the Canon IJ Network Tool screen, select LAN connection, then click OK.

IMPORTANT
Set the machine's LAN setting to Wireless LAN active beforehand.
For details, refer to "Machine's LAN Setting"

2. If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK.

3. Select Setup in the pop-up menu, select **** series in Printers, then click OK.

REFERENCE
[****] is your machine's name.

4. Detect Access Point.

When the Access Points screen appears, select an access point to use, then click Connect.
When an access point is detected automatically, the Access Points screen does not appear. Go to step 5.

IMPORTANT
To connect to the access point with WEP or WPA displayed in the Encryption column, enter the network key (WEP key or WPA key) in Network Password, then click Connect.

5. Detect the Machine.

When the Set Printer IP Address screen appears, confirm the contents, then click Connect.
If the machine is detected automatically, the Set Printer IP Address screen does not appear. Go to step 6.

6. When the Setup Completion dialog box appears, remove the USB cable, then click Next.

7. Press the ON button (A) TO TURN OFF THE MACHINE, then place the machine in the location where you will use it, and turn on it.

8. On the Connection Performance Measurement dialog box, click Next.

Measuring of the communication status starts, and the results are displayed.

REFERENCE
Measuring takes a few minutes.
Measuring can be cancelled by clicking Cancel. You also examine the detailed status of the communication link after setup by using the Canon IJ Network Tool.

9. Confirm the measurement results, then click Finish.

Ensure that is displayed in Connection performance between the printer and the access point.
The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.

REFERENCE

• If any symbol other than is displayed, refer to displayed comments and Help for improving the status of communication link.
• To check whether the new location is better, click Remeasurement. Measurement of the communication status is performed again.
• When any message on Overall network performance appears in the measurement results, rearrange the printer and other network devices following the instructions on the screen.

• Add the Machine

1. Mac OS X v.10.4.x/v.10.3.9

When the Printer List screen appears, click Add.
Mac OS X v.10.4.x:
Go to Step 2
Mac OS X v.10.3.9:
Go to Step 3

NOTE
In the following instructions, "****" signifies your machine's name.

2. Mac OS X v.10.5.x/v.10.4.x

Wait for a while, then select Canon **** series and click Add.
In Mac OS X v.10.4.x, click More Printers in the Printer Browser screen.
- Mac OS X v.10.5.x:
Go to Step 5
- Mac OS X v.10.4.x:
Go to Step 3

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

3. Mac OS X v.10.4.x/v.10.3.9

Select Canon IJ Network in the pop-up menu, select your machine's name in the list of printers, then click Add.

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

4. Mac OS X v.10.4.x/v.10.3.9

Confirm that your machine's name is added to the list of printers.

5.

On the Canon IJ Network Scanner Selector screen, select Canon **** series Network in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner.

REFERENCE
With Mac OS X v.10.5.x, the Card Slot is not available when using the machine over a network.

Install the Software(First-time Setup for Use over Wireless LAN)

WPS Connection

If your access point supports WPS (Wi-Fi Protected Setup), you can set the wireless LAN security easily.

1. Use the Easy-Scroll Wheel (A) or the or button to select Settings, then press the OK button.

2. Select Device settings, then press the OK button.

3. Select LAN settings, then press the OK button.

4. Select Change wireless/wired, then press the OK button.

5. Select Wireless LAN active, then press the OK button.

6. Select Wireless LAN settings, then press the OK button.

7. Select WPS settings, then press the OK button.

8. Select Push button method, then press the OK button.

REFERENCE
To use the PIN code method for setup, select PIN method on step 8, then press the OK button. Follow the on-screen is instructions to operate the machine and access point. When the setup is complete, the completion screen appears then the LAN settings screen returns. A timeout error occurs if setup is not completed within 10 minutes.

9. Press the OK button.

10. When the access point is ready, press the OK button on the machine, then press the WPS button on the access point within two minutes.

The completion screen appears on the LCD of the machine, then the LAN settings screen returns.

IMPORTANT
A timeout error occurs if setup is not completed within two minutes.

REFERENCE
The WPS button may be named differently depending on your access point. For details, refer to the manual of your access point.

Windows

NOTE
If the Found New Hardware or Found New Hardware Wizard screen appears:

(1) Remove the USB cable connected to your computer.
The screen may close. In this case, proceed from 1.
(2) Click Cancel to quit the screen.
(3) Proceed from 1.

1. Press the ON button (A) to TURN OFF THE MACHINE.

IMPORTANT
Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing.

2. Turn on the computer, then insert the
Setup CD-ROM into the CD-ROM drive.
The setup program should run automatically.

• Windows Vista:

Go to Step 3

• Windows XP/2000:

Go to Step 5

REFERENCE
If the program does not start automatically, double-click the CD-ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

3. AutoPlay screen appears, click Run Msetup4.exe.

4. User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8.　Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

• Connect the Wired LAN / Wireless LAN

1. Press the ON button (A) to TURN ON THE MACHINE.

IMPORTANT

• Make sure that the computer you are setting up is not connected to the machine with a USB cable.
• For wired LAN connections, confirm that the machine is connected to the network with a LAN cable.

2. On the Setup Method screen, select Printer is already connected to the network, then click Next.

3. When the Printers screen appears, make sure that the machine is selected and click Next.

- Windows Vista:
Go to Step 5
- Windows XP/2000:
Go to Step 4

IMPORTANT

• When the machine is not detected, make sure of the following, click Update.

- The machine is turned on.
- When using wireless LAN : The computer is connected to the access point.
- When using wired LAN : The machine is connected to the network device with the LAN cable.

• Some programs that switch the network environment depending on your environment will enable a firewall by default. Check the settings of any such software.

4. Windows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

5. When the Setup Completion screen appears, click Finish.

REFERENCE
To change the port name, click View Setup Results, then click Set Port Name.

• Information

1. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

2. Click Next.
It may take a while for the next screen to appear. Click Next only once.

3. Click Next.
If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

4. When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

5. Click Exit.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

Macintosh

1. Connect one end of the USB cable to the computer and the other to the machine.
Make sure the machine is turned on.

REFERENCE

• The USB port is located on the right side at the back of the machine.
• When using WPS (Wi-Fi Protected Setup) or connecting an

additional computer, make sure that the machine is turned on, then go to step 2. It is not necessary to connect the machine to the computer with a USB cable.

2. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

3. Double-click the Setup icon.
If the CD-ROM folder does not open automatically, double-click the CANON_IJ icon on the desktop.

4. Enter your administrator name and password. Click OK.
If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8. Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

9. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

10. Click Next.

11. Click Next.
If connected to the Internet, the user registration page appears.
Follow the on-screen instructions to register your product.
You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

12. Click Restart.
When the computer restarts, Canon IJ Network Tool starts automatically.
Click Restart to restart the computer.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

REFERENCE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.

• Connect the Wired LAN / Wireless LAN

1. On the Canon IJ Network Tool screen, select LAN connection, then click OK.

2. If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK.

3. Select Setup in the pop-up menu, then click Register Printer.

4.

When the Cancel Setup screen appears, then click Cancel.
The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.

REFERENCE
When the You have no printers available. screen appears, click Cancel.

• Add the Machine

1. Mac OS X v.10.4.x/v.10.3.9

When the Printer List screen appears, click Add.
Mac OS X v.10.4.x:
Go to Step 2
Mac OS X v.10.3.9:
Go to Step 3

NOTE
In the following instructions, "****" signifies your machine's name.

2. Mac OS X v.10.5.x/v.10.4.x

Wait for a while, then select Canon **** series and click Add.
In Mac OS X v.10.4.x, click More Printers in the Printer Browser screen.
- Mac OS X v.10.5.x:
Go to Step 5
- Mac OS X v.10.4.x:
Go to Step 3

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

3. Mac OS X v.10.4.x/v.10.3.9

Select Canon IJ Network in the pop-up menu, select your machine's name in the list of printers, then click Add.

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

4. Mac OS X v.10.4.x/v.10.3.9

Confirm that your machine's name is added to the list of printers.

5.

On the Canon IJ Network Scanner Selector screen, select Canon **** series Network in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner.

REFERENCE
With Mac OS X v.10.5.x, the Card Slot is not available when using the machine over a network.

Install the Software (WPS Connection)

WCN Connection

You can set the wireless LAN security on the machine easily by using the WCN (Windows Connect Now) function of Windows Vista together with a USB flash drive.

IMPORTANT

• Canon assumes no responsibility for any damage or loss of stored data regardless of the cause.
• If your USB flash drive cannot be attached to the direct print port of the machine, an extension cord for USB flash drives may be required. Purchase one at an electronics shop.
• Operation may not be guaranteed depending on your USB flash drive.
• USB flash drives with security enabled may not be used.

REFERENCE
The machine supports "WCN-UFD".

1. From the Start menu of the Windows side, click Network.
The Network folder opens.

2. Click Add a wireless device on the menu.
The Add a wireless device to the Network screen will be displayed.

3. Click I want to add a wireless device or computer that is not on the list, using a USB flash drive.

4. Click Add the device or computer using a USB flash drive.

5. From the list, select the network name (SSID), then click Next.

REFERENCE
If the User Account Control screen appears, click Continue. If the same screen reappears in subsequent steps, click Continue.

6. Connect the USB flash drive to the computer, confirm that the drive name is displayed, then click Next.

7.

When the above screen appears, remove the USB flash drive
from the computer, then click Close.

8. Use the Easy-Scroll Wheel (A) or the or button to select Settings, then press the OK button.

9. Select Device settings, then press the OK button.

10. Select LAN settings, then press the OK button.

11. Select Change wireless/wired, then press the OK button.

12. Select Wireless LAN active, then press the OK button.

13. Select Wireless LAN settings, then press the OK button.

14. Select WCN settings, then press the OK button.

15. Connect the USB flash drive to the direct print port
(USB connector) on the front of the machine, then
press the OK button.

The completion screen appears on the LCD of the machine, then the LAN settings screen returns. Remove the USB flash drive from the machine.

Windows

NOTE
If the Found New Hardware or Found New Hardware Wizard screen appears:

(1) Remove the USB cable connected to your computer.
The screen may close. In this case, proceed from 1.
(2) Click Cancel to quit the screen.
(3) Proceed from 1.

1. Press the ON button (A) to TURN OFF THE MACHINE.

IMPORTANT
Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing.

2. Turn on the computer, then insert the
Setup CD-ROM into the CD-ROM drive.
The setup program should run automatically.

• Windows Vista:

Go to Step 3

• Windows XP/2000:

Go to Step 5

REFERENCE
If the program does not start automatically, double-click the CD-ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

3. AutoPlay screen appears, click Run Msetup4.exe.

4. User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8.　Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

• Connect the Wired LAN / Wireless LAN

1. Press the ON button (A) to TURN ON THE MACHINE.

IMPORTANT

• Make sure that the computer you are setting up is not connected to the machine with a USB cable.
• For wired LAN connections, confirm that the machine is connected to the network with a LAN cable.

2. On the Setup Method screen, select Printer is already connected to the network, then click Next.

3. When the Printers screen appears, make sure that the machine is selected and click Next.

- Windows Vista:
Go to Step 5
- Windows XP/2000:
Go to Step 4

IMPORTANT

• When the machine is not detected, make sure of the following, click Update.

- The machine is turned on.
- When using wireless LAN : The computer is connected to the access point.
- When using wired LAN : The machine is connected to the network device with the LAN cable.

• Some programs that switch the network environment depending on your environment will enable a firewall by default. Check the settings of any such software.

4. Windows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

5. When the Setup Completion screen appears, click Finish.

REFERENCE
To change the port name, click View Setup Results, then click Set Port Name.

• Information

1. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

2. Click Next.
It may take a while for the next screen to appear. Click Next only once.

3. Click Next.
If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

4. When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

5. Click Exit.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

Install the Software (WCN Connection)

To set up an additional computer (LAN)

Windows

NOTE
If the Found New Hardware or Found New Hardware Wizard screen appears:

(1) Remove the USB cable connected to your computer.
The screen may close. In this case, proceed from 1.
(2) Click Cancel to quit the screen.
(3) Proceed from 1.

1. Press the ON button (A) to TURN OFF THE MACHINE.

IMPORTANT
Operating noise continues for about 30 seconds until the machine turns off. Make sure that the POWER lamp (B) stops flashing.

2. Turn on the computer, then insert the
Setup CD-ROM into the CD-ROM drive.
The setup program should run automatically.

• Windows Vista:

Go to Step 3

• Windows XP/2000:

Go to Step 5

REFERENCE
If the program does not start automatically, double-click the CD-ROM icon on the computer. When the CD-ROM contents appear, double-click MSETUP4.EXE.

3. AutoPlay screen appears, click Run Msetup4.exe.

4. User Account Control screen appears, click Continue.
If the same screen reappears in subsequent steps, click Continue.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8.　Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

• Connect the Wired LAN / Wireless LAN

1. Press the ON button (A) to TURN ON THE MACHINE.

IMPORTANT

• Make sure that the computer you are setting up is not connected to the machine with a USB cable.
• For wired LAN connections, confirm that the machine is connected to the network with a LAN cable.

2. On the Setup Method screen, select Printer is already connected to the network, then click Next.

3. When the Printers screen appears, make sure that the machine is selected and click Next.

- Windows Vista:
Go to Step 5
- Windows XP/2000:
Go to Step 4

IMPORTANT

• When the machine is not detected, make sure of the following, click Update.

- The machine is turned on.
- When using wireless LAN : The computer is connected to the access point.
- When using wired LAN : The machine is connected to the network device with the LAN cable.

• Some programs that switch the network environment depending on your environment will enable a firewall by default. Check the settings of any such software.

4. Windows XP/2000
When the Network Setup of the Card Slot dialog box appears, specify the drive letter, then click Next.

5. When the Setup Completion screen appears, click Finish.

REFERENCE
To change the port name, click View Setup Results, then click Set Port Name.

• Information

1. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

2. Click Next.
It may take a while for the next screen to appear. Click Next only once.

3. Click Next.
If connected to the Internet, the user registration page appears. Follow the on-screen instructions to register your product. You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

4. When the Extended Survey Program screen appears, confirm the message. If you can agree,click Agree.
If you click Do not agree, the Extended Survey Program will not be installed. (This has no effect on the machine's functionality.)

5. Click Exit.
If Restart is displayed, make sure that the Restart the system now (recommended) check box is selected, then click Restart.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

Macintosh

1. Connect one end of the USB cable to the computer and the other to the machine.
Make sure the machine is turned on.

REFERENCE

• The USB port is located on the right side at the back of the machine.
• When using WPS (Wi-Fi Protected Setup) or connecting an

additional computer, make sure that the machine is turned on, then go to step 2. It is not necessary to connect the machine to the computer with a USB cable.

2. Turn on the computer, then insert the Setup CD-ROM into the CD-ROM drive.

3. Double-click the Setup icon.
If the CD-ROM folder does not open automatically, double-click the CANON_IJ icon on the desktop.

4. Enter your administrator name and password. Click OK.
If you do not know your administrator name or password, click Help, then follow the on-screen instructions.

5. When the Select Your Place of Residence screen appears, select your place of residence, then click Next.

REFERENCE
If the Select Language screen appears, select a language, then click Next.

6. Click Easy Install.
The drivers, application software, and on-screen manuals are installed automatically.

REFERENCE
If you want to select particular items to install, click Custom Install and follow the on-screen instructions to proceed with the installation.

7. Click Install.
Move the cursor over items to display explanations.

8. Read the License Agreement screen carefully and click Yes.
Installation starts.

IMPORTANT
Follow any on-screen instructions to install the software.

9. When the Load plain paper into the cassette screen appears, load plain paper in the Cassette (A) and click Next.

10. Click Next.

11. Click Next.
If connected to the Internet, the user registration page appears.
Follow the on-screen instructions to register your product.
You will need your product serial number, which is located on the inside of the machine.

IMPORTANT
Internet connection is required. (Connection fees apply.)

REFERENCE
To register later, click Cancel. User Registration can be started from the Solution Menu icon.

12. Click Restart.
When the computer restarts, Canon IJ Network Tool starts automatically.
Click Restart to restart the computer.
After restarting the computer, remove the Setup CD-ROM and keep it in a safe place.

REFERENCE
When using Mac OS X v.10.3.9, before using the Operation Panel on the machine to save scanned originals to the computer, it is necessary to select MP Navigator EX as the launch application on Image Capture under Applications.

• Connect the Wired LAN / Wireless LAN

1. On the Canon IJ Network Tool screen, select LAN connection, then click OK.

2. If the Setup Preparations dialog box appears, confirm that preparation is complete, then click OK.

3. Select Setup in the pop-up menu, then click Register Printer.

4.

When the Cancel Setup screen appears, then click Cancel.
The Printer Setup Utility and Canon IJ Network Scanner Selector will start up.

REFERENCE
When the You have no printers available. screen appears, click Cancel.

• Add the Machine

1. Mac OS X v.10.4.x/v.10.3.9

When the Printer List screen appears, click Add.
Mac OS X v.10.4.x:
Go to Step 2
Mac OS X v.10.3.9:
Go to Step 3

NOTE
In the following instructions, "****" signifies your machine's name.

2. Mac OS X v.10.5.x/v.10.4.x

Wait for a while, then select Canon **** series and click Add.
In Mac OS X v.10.4.x, click More Printers in the Printer Browser screen.
- Mac OS X v.10.5.x:
Go to Step 5
- Mac OS X v.10.4.x:
Go to Step 3

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

3. Mac OS X v.10.4.x/v.10.3.9

Select Canon IJ Network in the pop-up menu, select your machine's name in the list of printers, then click Add.

REFERENCE

• The alphanumeric string after Canon **** series is the machine's MAC address.
• If the machine has not been detected, make sure of the following.

- The machine is turned on.
- The firewall function of any security software is turned off.
- Wired LAN Connection: The machine is connected to the network device with the LAN cable.
- Wireless LAN Connection: The computer is connected to the access point.
- The machine is not set to use access control (MAC address filtering).

4. Mac OS X v.10.4.x/v.10.3.9

Confirm that your machine's name is added to the list of printers.

5.

On the Canon IJ Network Scanner Selector screen, select Canon **** series Network in TWAIN Data Source Name and the MAC address of the machine in Network Device List, then click Apply to use the machine as a scanner.

REFERENCE
With Mac OS X v.10.5.x, the Card Slot is not available when using the machine over a network.

Install the Software (To set up an additional computer)